Universal Pulse Generators

U_max = -3kV | I_max = (40)A |  P_average = 0.03kW

For capacitive loads, allows to switch between a negative voltage of -7.5kV....0V and a positive voltage of 0...+7.5kV
U_max = ±7.5kV | I_max = 5A |  P_average = 2*0.5kW

Special version with two outputs which can be shifted in phase.
U_max = 2x6kV | I_max = 5A |  P_average = 0.7kW

Special version for an ion source; two outputs which are synchronously switched.
U_max = -+5 - 0.1kV | I_max = 6A |  P_average = 10kW
U_max = -+0.2 - (-0.8)kV

U_max = -2.2kV | I_max = (40)A |  P_average = 0.01kW

Additionally up to -200V bias.
U_max = -2kV | I_max = 10A |  P_average = 0.2kW

U_max = +5kV | I_max = 1A |  P_average = 0.1kW

Especially for ion sources, in the state "off" there is a slightly positive voltage (current limited) at the output.
U_max = -5kV | I_max = 1A |  P_average = 0.1kW

Output resistor is exchangeable, therefore rise and fall time can be adjusted.
U_max = +5kV | I_max = 10A |  P_average = 0.024kW

RUP can be controlled via RS232 interface.
U_max = +5kV | I_max = 1A |  P_average = 0.1kW

U_max = -5kV | I_max = 2A |  P_average = 0.9kW

OEM-version
U_max = +9kV | I_max = 12A |  P_average = 0.012kW

OEM version, output capacitively coupled, potential free.
U_max = +10kV | I_max = 5A |  P_average = 0.003kW

U_max = +10kV | I_max = 3A |  P_average = 0.015kW

Special version with AC bias up to ±200V
U_max = +10kV +(±200V bias) | I_max = 10A |  P_average = 0.9kW

U_max = -15kV | I_max = 5A |  P_average = 0.75kW

U_max = +25kV | I_max = 1A |  P_average = 0.025kW

Special version with two outputs, designed for high voltage magnetron sputtering.
U_max = -3kV | I_max = 2*40A |  P_average = 1.2kW
German

Modified topology for voltage testing of inductive as well as capacitive loads
U_max = -10kV | I_max = 200A |  P_average = 2.5kW

Universal device for small average power, 5HE desktop housing.
U_max = -1kV | I_max = 100A |  P_average = 0.1kW

Optimized for capacitive loads, rise time can be varied in a broad range.
Umax = -12kV | Imax = 100A | Paverage = 2.5kW

Designed for high power arc coating machines.
U_max = -3kV | I_max = 200A |  P_average = 2.5kW

Additional lower voltage, high current mode (-1kV, 2.5A average), and -200V, 1A bias supply.
U_max = -6kV | I_max = 50A |  P_average = 2.5kW

Special version for 3*480V supply voltage and a high voltage relais in the output.
U_max = -12kV | I_max = 120A |  P_average = 6kW

U_max = -22kV | I_max = 50A |  P_average = 2.5kW

Also availible with -200V bias as RUP6-22B

U_max = -6kV | I_max = 60A |  P_average = 2.5kW

U_max = -35kV | I_max = 60A |  P_average = 2.5kW

U_max = -17kV | I_max = 200A |  P_average = 12kW

In contrary to standard RUP6 there are full bridges instead of half bridges on the pulse modules. Therefore both polarities are possible, even arbitrary pulses with alternating polarity.
All bipolar RUP6 have adjustable ramp times and were designed for insulation testing applications.
U_max = ±25kV | I_max = 50A |  P_average = 2kW

 

U_max = ±18kV | I_max = 50A |  P_average = 2kW

RUP7 with 2 operating modes for plasma coating applications

U_max = 1kV / 2kV | I_max = 200A / 400A |  P_average = 15kW

Current is controlled by analog control signal, nearly arbitrary waveforms can be generated.
U_max = 400V | I_max = 2500A |  P_average = 3.2kW

Peak current 5000A.Enhanced version of RUP7MV
U_max = 400V | I_max = 5000A |  P_average = 3.2kW

RUP8 with 90kV